The search coils for Blackdog metal detectors are interchangeable with the detector models of the major market brands. The Blackdog coils have been designed to significantly increase the depth and area of search for objects in areas where objects have previously been searched for with standard coils included in the various brands of detectors on the market.

UV-treated ABS plastic that is high impact. 99 percent pure copper winding for improved electrical conductivity. To increase the «Q» factor, which results in a larger magnetic field and a deeper detector, the quality of the winding is crucial. The cable is custom-made and has a protective covering 99 percent of its inside surface. To keep it from separating when subjected to pulls, it is further reinforced with textile fibers. To survive high temperatures without losing its qualities, the resin employed is an epoxy type with UV protection and a very high glass transition coefficient (TG).

Temperatures beyond 120 degrees are no match for our resin. All of Blackdog coils go through a post-curing procedure in a unique oven to ensure that the resin keeps its properties despite the temperature variations that the coils are exposed to. To get the most out of our goods, each of our coils is carefully tuned utilizing oscilloscopes and laboratory equipment.

SPECIFICATIONS

• Double D coil for improved discrimination and target location.
• Improved penetration in the mineralized ground or beneath ceramics.
• More stability, allowing the detector’s sensitivity to be increased.
• The coils are double shielded with low capacitance graphite, which eliminates electrical interference and false signals in wet terrain, wet grass, rubbing against plants, and wet sandy beaches.
• Dish which is completely submersible and waterproof
• Depending on the type of detector, depth can be increased by up to 70% when compared to standard coils.
• A coil protector is included.
• Depending on the detector model, the winding may differ.

The post Ace Apex Blackdog Max Coil appeared first on Golden Spark Detectors | Dubai UAE.

UV-treated ABS plastic that is high impact. 99 percent pure copper winding for improved electrical conductivity. To increase the «Q» factor, which results in a larger magnetic field and a deeper detector, the quality of the winding is crucial. The cable is custom-made and has a protective covering 99 percent of its inside surface. To keep it from separating when subjected to pulls, it is further reinforced with textile fibers. To survive high temperatures without losing its qualities, the resin employed is an epoxy type with UV protection and a very high glass transition coefficient (TG).

Temperatures beyond 120 degrees are no match for our resin. All of Blackdog coils go through a post-curing procedure in a unique oven to ensure that the resin keeps its properties despite the temperature variations that the coils are exposed to. To get the most out of our goods, each of our coils is carefully tuned utilizing oscilloscopes and laboratory equipment.

SPECIFICATIONS

• Double D coil for improved discrimination and target location.
• Improved penetration in the mineralized ground or beneath ceramics.
• More stability, allowing the detector’s sensitivity to be increased.
• The coils are double shielded with low capacitance graphite, which eliminates electrical interference and false signals in wet terrain, wet grass, rubbing against plants, and wet sandy beaches.
• Dish which is completely submersible and waterproof
• Depending on the type of detector, depth can be increased by up to 70% when compared to standard coils.
• A coil protector is included.
• Depending on the detector model, the winding may differ.

BRANDS COMPATIBLES

The post Blackdog Max Deep Coils appeared first on Golden Spark Detectors | Dubai UAE.

We are proud to introduce the new Blackdog Gladiator, one of our greatest metal detectors that will certainly leave its imprint on the global market.

• Includes an upgraded 33 x 33 cm Blackdog Platter that is lighter, has a faster recovery time and was calibrated by electronic engineers using an oscilloscope.
• A 3400 mAh lithium-ion rechargeable battery with 60 h
• New and improved software

The post Gladiator Metal Detector appeared first on Golden Spark Detectors | Dubai UAE.

DELAY: Helps in the removal of small metallic objects found at shallow depths as well as the cancellation of ground mineralization. The lower the value, the greater the depth. Unwanted objects such as bits of aluminum foil, bits of lead, or other metals can be rejected by increasing the value, but the depth of the detector may be affected.

TX-BOOST: This control regulates the width of the transmission pulse. When it is set to a high value, the depth increases, but the current consumption rises. To avoid false signals, it is recommended to lower the value for searches in mineralized areas.

FREQ: It refers to the frequency control, which can be set between 95Hz and 125Hz. This control aids in the elimination of electrical interference when conducting searches near power lines or other sources of interference. We seek a slight threshold level for optimum frequency adjustment using the GAIN setting. If we notice a lot of variation in the threshold tone, we slowly turn the FREQ adjustment control to the right or left until we get the sharpest possible threshold tone. Level 3 is recommended.

VOLUME: The device’s volume control is used to adjust the intensity of the sound emitted by the speaker. This control has no effect on the device’s depth.

GAIN: the device’s gain or sensitivity control.

GROUND: We disable the effects of ground mineralization with this setting.

RESET: In the event of a mismatch, this button is used to reset the detector. It is recommended that you press it for 2-3 seconds after changing any detector parameter.

USE OF THE DETECTOR

According to figures 1 and 2, assemble the frame coil.

Through the connector, attach the coil to the detector.

Stand within the box while wearing the detector around your neck.

the following settings for the potentiometers

DELAY at position “0”

GROUND is Positioned at “10”

TX-BOOST in Position “10”

FREQ in “3” position

Gain in place “10”

Volume is set at “5”.

Place the box on a clean, metal-free floor. Turn on the detector by pressing the POWER button. The detector will make a sound, then press and hold the RESET button for 3 seconds to silence it. If the detector continues to make noise, press the RESET button again until it is silent. The detector would be ready to search with these settings.

Begin walking slowly by grasping the frame straps with both hands. When the detector detects a metal object, it will beep and the DEPTH bar will gradually light up depending on the depth and size of the detected object. The detector can distinguish between small metallic objects on the surface.

If the signal’s tone rapidly rises and falls in a small area, it indicates that the object is small and has a depth of up to 50 cm.

When the signal tone increases in a medium-sized area and then gradually decreases, it indicates the discovery of a medium-sized object at a depth of up to 3 meters, as shown in Fig.3.

When the signal tone increases over a large area and then gradually decreases, it indicates the finding of a medium-sized object at a depth of up to 8 meters, as shown in Fig.4.

To avoid the effects of mineralization, set the GROUND potentiometer to “9” if the search is being conducted in highly mineralized terrain. If the ground is overly mineralized, you can reduce the effects by increasing the DELAY value while decreasing the TX-BOOST and GAIN values.

If you search near power lines and the detector is affected by interference, you can minimize these effects by using the FREQ control.

MAINTENANCE:

The detector is powered by a 3400mAh Li-ION battery with a range of 15 to 30 hours of search time depending on the numerical position of the TX-BOOST button. When the battery level LED illuminates, it is time to charge the detector. The charging time is approximately 3-4 hours, until the charger light turns green. The supplied charger is both automatic and safe.

If you charge the batteries with anything other than the charger supplied by the manufacturer, the detector’s warranty will be voided.

Cleaning the detector is advised with a wet cotton cloth. Chemical products should not be used since they could harm the aesthetics of the device and its accessories.

In any room of the house where there are metallic objects, never use the detector.

Never touch the detector inside. 500 Volts of electrocution risk.

If the frame coil is not deployed, do not turn on the detector as it will be harmed. The frame coil should not be submerged in water because it is not waterproof.

The  Blackdog X-Treme Metal Detector includes:

• Frame 1×1 meter.
• Carbon fiber telescopic crutch.
• 13×13 inch Monoloop coil.

The post X-TREME Metal Detector appeared first on Golden Spark Detectors | Dubai UAE.

DELAY: Helps in the removal of small metallic objects found at shallow depths as well as the cancellation of ground mineralization. The lower the value, the greater the depth. Unwanted objects such as bits of aluminum foil, bits of lead, or other metals can be rejected by increasing the value, but the depth of the detector may be affected.

TX-BOOST: This control regulates the width of the transmission pulse. When it is set to a high value, the depth increases, but the current consumption rises. To avoid false signals, it is recommended to lower the value for searches in mineralized areas.

FREQ: The term refers to the frequency control, which has a range of 95Hz to 125Hz. If searches are conducted close to power lines or other sources of interference, this control helps in the elimination of electrical interference. With the help of the GAIN setting, we search for a slight threshold level for the best frequency adjustment. If the threshold tone appears to have many changes, we gradually turn the FREQ adjustment control to the right or left until the threshold tone is as crisp as it can be. Level 3 is advised.

VOLUME: The device’s volume control is used to control how loud the sound coming from the speaker is. The device’s depth is unaffected by this control in any way.

GAIN: The device’s gain or sensitivity control.

GROUND: By using this setting, ground mineralization’s effects are completely eliminated.

In the event of a mismatch, this button is used to reset the detector. It is advised to press it for two to three seconds after changing any detector parameter.

MENU: Just like the LCD screen, this control is only effective in VLF mode.

POWER: There are three places on this switch. The PI detector is on in the rear position, the VLF in the middle, and the gadget is completely off in the forward position.

PI MODE START-UP:

According to figures 1 and 2, assemble the frame coil.

Through the connector, attach the coil to the detector.

Stand within the box while wearing the detector around your neck.

the following settings for the potentiometers

DELAY at position “0”

GROUND is Positioned at “10”

TX-BOOST in Position “10”

FREQ in “3” position

Gain in place “10”

Volume is set at “5”.

Place the box on a spotless surface devoid of any metal objects. Use the POWER switch to turn on the detector. The switch should be in the back position. After pressing and holding the RESET button for three seconds while the detector makes a sound, it should stop making noise. Press the RESET button once more until the detector is silent if it still makes any noise. The detector would be prepared for the search with these settings.

With both hands holding the frame straps, carefully begin to move forward. The DEPTH bar will gradually light up and the detector will beep when it detects a metal object, depending on its size and depth. Small metallic items lying on the surface can be distinguished by the detector.

The item is small and has a depth of up to 50 cm if the tone of the signal fluctuates sharply in a narrow area.

As illustrated in Fig. 3, a medium-sized object has been discovered at a depth of up to 3 meters when the signal tone increases in a medium-sized area before slowly decreasing again.

As illustrated in Fig. 4, when the signal tone gradually declines after increasing across a vast area, it indicates the discovery of a medium-sized object at a depth of up to 8 meters.

You must set the GROUND potentiometer to position “9” if the search is being conducted in an area with significant mineralization in order to mitigate its impacts. Increase the DELAY value while decreasing the TX-BOOST and GAIN values to lessen the effects if the ground is overly mineralized.

With the use of the FREQ control, you can lessen the impacts of interference on the detector when searching close to power lines.

MAINTENANCE:

Depending on the numerical position of the TX-BOOST button, the detector’s extremely powerful 3400mAh LI-ION battery may operate independently for 15 to 30 hours of searching. When the battery level LED illuminates, you should recharge the detector. Until the charger indicator turns green, the charging process takes about 3 to 4 hours. The charger that is provided is automatic and secure.

Never attempt to charge the batteries using a charger other than the one provided by the manufacturer to avoid voiding the detector’s warranty.

Cleaning the detector is advised with a wet cotton cloth. Chemical products should not be used since they could harm the aesthetics of the device and its accessories.

In any room at home where there are metallic objects, never use the detector.

Never touch the detector inside. 500 Volts of electrocution risk.

If the frame coil is not deployed, do not turn on the detector as it will be harmed. The frame coil cannot be submerged in water because it is not submersible.

VLF MODE START-UP;

Using the plastic screw that is included, mount the DD coil on the telescoping crutch.

Through the connector, attach the coil to the detector.

Suspend the detector from your neck.

With the POWER switch in the forward position, turn the detector on. The detector’s display will switch on and show you the main screen three seconds later. To see all the settings on the screen, press the MENU button. Select the first SENS option after entering, then hit the MENU button. You’ll see a 0–9 scale. Turn the MENU button to the right or left to choose the desired level. Press the MENU button after selecting the desired level, and “OK” will appear on the display. With each setting, we perform this action once more. Press EXIT once you have completed modifying all the parameters. The main screen will show up after all settings have been automatically saved.

The  Blackdog  HybridScan Metal Detector  includes:

• Frame 1×1 meter.
• Carbon fiber telescopic crutch.
• 13×13 inch DD coil.

The post Hybridscan Metal Detector appeared first on Golden Spark Detectors | Dubai UAE.